Grouts & Repairing Mortars

USES

 Hind Plast EGA can be used for Grouting in

• 1. Pre-stressed cable ducts.
• 2. Rock and soil anchoring.
• 3. Bearing plates.
• 4. Pre-placed aggregates.
• 5. Tunnel lining.
• 6. In underground structure, basement, tunnel, lift-wells, dams, water reservoir and other water retaining structure.
• Does not allow shrinkage of cement used in cement sand mortar.

ADVANTAGES

• 1. Improved fluidity.
• 2. Increased cohesion.
• 3. Volume expansion in the wet state to develop non-shrink property.
• 4. Chloride free – does not attack reinforcement or pre-stress cables

APPLICATION

The recommended dosage range is 0.5 to 0.6 kg. per 100 kgs. Cement. It is advisable to conduct trials to achieve optimum economical dose.Add directly to the dry cement then add water into the mixer and mix at least for 3 minutes. Sand may be added  if required. For pre-stressed concrete work, where mechanical batching is carried out, a mixing time of 4 minutes with a w/c ratio of 0.36 – 0.40 has been found to give the best result. The most effective mixing sequence has proven to be water, cement and finally the admixture. When used as an admixture to compensate the drying shrinkage of cement in mortar the recommended dosage varies from 0.1% to 0.25% by weight of cement.

PROPERTIES

SHELF LIFE

6 months from the date of manufacture in unopened condition. To be stored in a cool and dry covered space away from  direct sunlight.

PACKING

250gm , 1 & 20 Kg in HDPE Bag or as required.

HANDLING PRECAUTION

Hind Plast EGA is non-toxic, non-inflammable and   ingestion is to avoided. If contact with eyes occur, Immediately wash with water and seek medical advice.

USES

Hind Grout GP is used for grouting of Bolt Pockets and Base plates grouting of all equipments, Columns in pre-cast construction concrete, Girders, Beams, Repair & Rehabilitation of Structures.

ADVANTAGES

Hind Grout GP is an economical and easy to use material, requiring only addition of water. It is very easy to mix and placement can be done with high flow characteristic, rapid strength development, adjustable consistency and Compressive strength up to 40N/mm² (28 days) is achieved. It does not segregate and bleed. It is impact and vibration resistant, non-corrosive to steel and iron, non-toxic and safe to handle.

APPLICATION

All grouting areas must be free from the loose concrete, oil, grease, and dust where Hind Grout GP will be placed. The grouting areas to be saturated with water and it is to be ensured that no stagnant water is present before application. Add Hind Grout GP Powder to clean water as per the recommended dosages. Keep on mixing with a grout or concrete mixer till a smooth and even consistency is achieved. Mixed grout should be used within 15 minutes of preparation. After initial hardening of the grout, it should be kept damp either by wet hessian cloth or with water-ponding for a minimum of  seven days. Water and Powder ratio varies from 0.12 to 0.18 depending on the consistency requirement of the site. 25 Kg of the material will yield approximately 13.0 Litre of Fluid Grout and 12.0 Litre of Plastic Grout mix respectively. Placing conditions including temperature may have to be assessed before pouring the grout at site. Small trial batches may be tried to ascertain best working consistency.

PROPERTIES

SHELF LIFE

6 months from the date of manufacture in unopened condition. To be stored in a cool and dry covered space away from direct sunlight.

PACKING

25kg in Poly lined HDPE Bag.

HANDLING PRECAUTION

Hind Grout GP is non-toxic and ingestion is to be avoided.  If contact with eyes occurs, wash well immediately with water and seek medical advice.

USES

Hind Grout HS is used for grouting under the Bolt Pockets and base plate grouting of all equipments, grouting of foundation bolts for all types of machinery in cement, textile, paper & steel industries, bridge bearing pads, columns, precast construction.

ADVANTAGES

Hind Grout HS is an economical and easy to use material, requiring only addition of water. It is very easy to mix and placement can be done with high flow characteristic, rapid strength development, adjustable consistency and Compressive strength up to 70N/mm² (28 days) is achieved. It does not segregate and bleed. It is impact and vibration resistant, non-corrosive to steel and iron, non-toxic and safe to handle.

APPLICATIONS

All grouting areas must be free from the loose concrete, oil, grease, and dust where Hind Grout HS will be placed. The grouting area to be saturated with water and it is to be ensured that no stagnant water is present before application. Add Hind Grout HS Powder to clean water as per the recommended dosages. Keep on mixing with a grout or concrete mixer till a smooth and even consistency is achieved. Mixed grout should be used within 15 minutes of preparation. After initial hardening of the grout, it should be kept damp either by wet hessian cloth or with water-ponding for a minimum of  seven days. Water and Powder ratio varies from 0.12 to 0.13 depending on the consistency requirement of the site. 25 Kg of the material will yield approximately 12.0 Litre of Fluid Grout and 11.0 Litre of Plastic Grout mix respectively. Placing conditions including temperature may have to be assessed before pouring the grout at site. Small trial batches may be tried to ascertain best working consistency.

PROPERTIES

SHELF LIFE

6 months from the date of manufacture in unopened condition. To be stored in a cool and dry covered space away from direct sunlight

PACKING

25kg in Poly lined HDPE Bag.

HANDLING PRECAUTION

Hind Grout HS is non-toxic and ingestion is to be avoided.  If contacts with eyes occur, wash well immediately with water and seek medical advice.

HIGH STRENGTH NON-SHRINK CEMENTITIOUS GROUT

 DESCRIPTION

 Hind Grout HS (M) is a Ultra High Strength, Free Flowing Non Shrink, and Chloride Free Grout, conforming to BS-1881, Part 116-1983.

 USES

 Hind Grout HS (M) is used for grouting under the Bolt Pockets and base plate grouting of all equipments, grouting of foundation bolts for all types of machinery in cement, textile, paper & steel industries, bridge bearing pads, columns, precast construction.

 ADVANTAGES

 Hind Grout HS (M) is an economical and easy to use material, requiring only addition of water. It is very easy to mix and placement can be done with high flow characteristic, rapid strength development, adjustable consistency and Compressive strength of 70N/mm² (7 days) is achieved. It does not segregate and bleed. It is impact and vibration resistant, non-corrosive to steel and iron, non-toxic and safe to handle.

 APPLICATIONS

All grouting areas must be free from the loose concrete, oil, grease, and dust where Hind Grout HS (M) will be placed. The grouting area to be saturated with water and it is to be ensured that no stagnant water is present before application. Hind Grout HS (M) Powder to clean water as per the recommended dosages. Keep on mixing with a grout or concrete mixer till a smooth and even consistency is achieved. Mixed grout should be used within 15 minutes of preparation. After initial hardening of the grout, it should be kept damp either by wet hessian cloth or with water-ponding for a minimum of seven days. Water and Powder ratio to be used is 0.13.

25 Kg of the material will yield approximately 12.0 Litre of Fluid Grout and 11.0 Litre of Plastic Grout mix respectively. Placing conditions including temperature may have to be assessed before pouring the grout at site. Small trial batches may be tried to ascertain best working consistency.

 PROPERTIES

SHELF LIFE

6 months from the date of manufacture in unopened condition. To be stored in a cool and dry covered space away from direct sunlight

 PACKING

25Kg.  in Poly lined HDPE Bag.

HANDLING PRECAUTION

Hind Grout HS (M) is non-toxic and ingestion is to be avoided.  If contacts with eyes occur, wash well immediately with water and seek medical advice.

USES

Hind HSMC is used for repairs to damaged reinforced concrete members, for cover replacing concrete, resistance to weathering action, and places where free flow concrete is required to be placed and vibration is difficult. Most suitable for structural repairs of columns, beams by means of encasement, jacketing etc.

ADVANTAGES

• 1. Free Flow
• 2. High Strength
• 3. Pre weighted and packed so site batching faults are minimized.
• 4. Fast strength gain
• 5. Non shrink
• 6. Resistant to weathering action for having low permeability.
• 7. Chloride free.

APPLICATION

Preparation of surface

The surface of old concrete member should be properly prepared by chipping off all the loose concrete, exposed reinforcements should be cleaned and de-rusted manually or mechanically, anticorrosive coating of acrylic or epoxy base like Hind Anti Rust or Hind Anti Rust EZ to be applied on the de-rusted reinforcement, bonding coat based on Epoxy or Polymer latex like Hind Bond EBA or Hind Styrene BR to be applied on the surface of concrete, steel or plywood shuttering to be fixed within the time the bonding coat becomes tacky and does not set.

 MIXING

The micro concrete to be mixed in the ratio of 1:0.5 to1:0.75 (1 part powder of micro concrete chemical : 0.5 to 0.75,  12 mm down silt free stone aggregate) with a Water : Powder ratio of 0.21 .The micro concrete chemical and the coarse aggregate is to be dry mixed thoroughly first and then it is to be slowly poured in pre measured water in a mixing container and stirred thoroughly manually or by a power paddle to obtain a free flow uniform pourable mix.

POURING/PLACING

The mixed material is then poured manually or pumped into the gap between the concrete members and shuttering to get a self compacted screen concrete of thickness between 40mm to 125mm.No vibration is required except gentle tamping by a light weight tool.

PROPERTIES

CONSUMPTION

25 Kg of Hind HSMC will yield approximately 12 Litre fluid grout. The actual yield will depend on the quantity of coarse aggregate added.

PACKING

5, 25 Kg in HDPE Bags

SHELF LIFE

6 months from the date of manufacture in unopened condition. To be stored in a cool and dry covered space away from direct sunlight.

HANDLING PRECAUTION

Hind HSMC is non-toxic and ingestion is to be avoided.  If contacts with eyes occur, wash well immediately with water and seek medical advice.

READY TO USE TILE JOINT FILLER

DESCRIPTION

Hind Tile Grout is an ideal cementitous based, ready to use, gap filling material for wall and floor tiles like vitrified, ceramic, mosaic, marble and glazed tiles etc.

USES

Hind Tile Grout is used to filling up the wall and floor joints when tiles like vitrified, ceramic, mosaic, marble and glazed tiles etc. are fixed in residential and industrial buildings.

ADVANTAGES

• Ready to use, only Water/ Polymer ( 50% Polymer, 50% Water for better result) is to be added.
• It ensures excellent bond with different types of tiles.
• Makes the joints waterproof.
• Dust penetration resistant.
• Is unaffected and can withstand effects of mild detergents and cleaning agents.
• Cleaning becomes easy.

APPLICATION

Surface Preparation

All substrate must be structurally sound, clean and free from any contamination like grease, oil, loose particles etc. before application of Hind Tile Grout.

Mixing

Add 340-360 gms. Water/ Hind Crete Plus WPM (Acrylic Polymer, for better result) to 1 Kg of Hind Tile Grout by volume and mixing is to be done properly by a trowel to get a paste type consistency. Allow the Tile grout paste to settle for 10-12 minutes in the mixing pan. The paste is then applied to fill the joints by means of spatula, trowel and finally it is smoothened evenly to level and finish. Surplus grout paste is removed by a damp sponge. Care should be taken while cleaning the surplus grout from getting it pressed down before drying.  The tile grout is allowed to dry for hours after application. We must always ensure that tile grout should be filled into the joints, 24 hours after the tile fixing operation is completed.

PROPERTIES

PACKING

Available in 1 Kg Pack

SHELF LIFE

6 months from the date of manufacture, provided the material is stored in a perfectly dry place and in unopened conditions.

HANDLING PRECAUTION

Hind Tile Grout is non-toxic and inhalation of the powder material is to be avoided. If contact with eyes occurs was with plenty of water.

USES

• 1. Soil stabilization and effective ground water sealing.
• 2. Prevents collapsing of loose soil making concreting very easy in loose soil.
• 3. To provide a watertight, impermeable soil mass.

ADVANTAGES

• 1. Use of Hind Geo Grout for soil stabilization allows future plantations and development of greenery which is restricted by use of bentonite.
• 2. It thixotropic gel penetrates into very fine fissures of the soil strata making it to form a compact soil mass which resist collapsing of loose soil at the time of concrete placing.
• 3. Non-toxic, very safe to handle and eco-friendly.

APPLICATION

The entire pouch of 250 gm of Hind Geo Grout is added to 20 Ltr. of water and stirred properly until the entire quantity gets dissolved in the water. After 2-3 minutes of mixing the compound starts reacting chemically with water and slowly turns into a gel like compound. This gel is now poured into the formwork which stabilizes the loose soil from collapsing. Our recommended dosage for Hind Geo Grout is 0. 60 Kg per M²  area. However it is suggested to finalize the exact dosage depending on soil condition at site.

PROPERTIES

SHELF LIFE

12 months from the date of manufacture. Material should be stored in a perfectly covered dry place.

PACKING

Available in 250 gm Plastic Pouch pack.

HANDLING PRECAUTION

Hind Geo Grout is non-toxic and ingestion is to be avoided. If contact with eyes occurs, wash well immediately with water and seek medical advice.

USES

Hind Grout SST can be used as an additive for:

• 1. Concrete and masonry foundation walls
• 2. Concrete Piling work.
• 3. Rock and soil Stabilization and effective ground water sealing.
• 4. For injection grouting in underground structures, Basement, Tunnel, Lift wells, Water Reservoir, Dams, Manholes and other water retaining structures

ADVANTAGES

• 1. Reduces water permeability.
• 2. No heat is generated during the curing period resulting no damage of the casings.
• 3. Aquifer is protected from surface water intrusion.
• 4. Remains flexible and stable over a long period of time.
• 5. Ready to use and easy application..
• 6. Environmental friendly and non hazardous

APPLICATION

Add 50 litre of clean water to a 20 Kg bag of Hind Grout SST. Mixing to be done thoroughly for 5-7 minutes using a drill fitted with a stirrer, until a uniform consistency is obtained. The slurry formed to be injected within a time limit of 45-50 minutes with pump. Ensure that injection grouting is completed with the schedule time otherwise the pump hose will get clogged.

PROPERTIES

PACKING

Available in 20 Kg HDPE Bag

SHELF LIFE

Hind Grout SST is hygroscopic and absorbs moisture. Should be stored in a cool and dry place and in unopened conditions away from direct heat and sunlight. If care as stated is maintained a minimum shelf life of 5-7 years can be obtained. Do not keep used bags mouth open, always ensure that it is properly tied up to avoid ingress of moisture.

HANDLING PRECAUTION

Hind Grout SST is non-toxic and ingestion is to be avoided. Contact with eyes must be avoided. Use of Hand gloves is recommended.